There is a tool called DbFixIt you can install and run on your Palm to check to see if you have any database errors. This will also report the number of deleted records in each database. The registered version of this tool will also fix common database errors. By the time you need this you might be in a Catch-22 position where you cannot hotsync but you need to hotsync to install the tool. So to install the tool you will need to configure your hotsync manager (on your computer) and tell it not to synchronize the applications that are causing it to hang (the calendar in my case). When I ran the tool it told me that all the databases were fine and there were no records to delete. Later I tried hot syncing on a Windows XP machine, and much to my amazement the hotsync finished, but it did report an error:
Some handheld records were not copied to your PC. Your computer may be full or you may have reached the maximum allowed records on the desktop. To correct this situation, delete some records and perform a HotSync operation again.So my problem was that I had exceeded some fixed maximum number of records in the calendar. To test this theory I deleted a few records from the Palm's calendar and synced again, this time without incident. I then synced on the Windows Vista machine, and again, the sync ran without any issue.
Desktop = 6378, Handheld = 6375
So now the question is: is 6375 the maximum number of calendar records, and can this be changed? 
VBoxManage setextradata VMNAME "VBoxInternal/Devices/piix3ide/0/Config/IRQDelay" 1I shut down VirtualBox, opened a DOS window, changed directory to "C:\Program Files\Sun\xVM VirtualBox" and then issued the command replacing "VMNAME" with the name of my virtual machine. Then I restarted VirtualBox and continued the installation. This time the install completed properly. 
The Panasonic Lumix G1 (also here on PhotographyBLOG) will be the first of the micro 4/3rds cameras, it will have a flip out 3 inch display (it looks like it is fully articulated and can be turned face in to protect it, yeay! this was a feature I really loved on my Canon G1) with a 460K pixel resolution (which still might not be enough for manual focusing). It has a very high 1.44 million pixel resolution viewfinder (so that might be enough to do manual focusing on, but I found that the 900K pixel view finder on the Minolta A2 was not enough for this so I am expecting this will will not be enough, however Panasonic is using a different technology which effectively stacks the RGB pixels so it might be a much sharper display than the traditional pixel count implies.). It got HDMI output too, so you can inflict painful hours of slide shows on your friends and relatives. Digital Photography Review has a preview of it here.
I encountered the "busy drive" bug while checking to see if any of my Seagate drives might be affected. Quite ironic, you shutdown the system to check the serial numbers and drive labels; and then, when you power up the system again one of the drives is no longer responding to the BIOS. Seagate now has a few online tools that you can use to find out if you need new firmware - the best is to get the drive's serial number and enter it. If your drive is one that is known to be at risk they will send you to a page from which you can download a small ISO image that you can burn to CD and then boot from to flash the drive.
Seagate's firmware upgrade procedure is described here, if you have an X86 PC which can boot from CD then it is pretty simple to flash the drives (just detach all your other drives first to be on the safe side).
I was able to unbrick my drive that had entered the busy state by following this procedure. If you just unscrew the screw near the drive power connector a few turns, then you can slide some insulating material (say the corner of a business card) between the connector and the controller board quite easily. I used one of these RS-232 to TTL level shifters (here from www.robotcraft.ca) and used a pair of AA batteries to power it at 3 volts. For the connector to the RX/TX pins I used a piece of cable from an old computer case, one of the two pin headers that is used to connect the front panel (lights or switches) to the motherboard. This had the correct pin spacing but was slightly too thick to insert into the drive's socket, so I used sand paper to thin it down a bit. Once I had found a serial cable (which I have not used for many years) I was able to connect the drive to the computer and verify that it did have the "busy error" symptoms (the drive will keep sending, about once a minute, a string like "LED:000000CC FAddr:0025BF67" to the terminal). At this point things worked up to issuing the "Z" command to spin down the drive. For me as soon as I issued that command the drive would enter the busy error state. The command sequence looked like:
F3 T>/2 F3 2>Z LED:000000CC FAddr:0025BF67 LED:000000CC FAddr:0025BF67In the end I reviewed the various drive commands (a list is listed here) and noted that the "Z" command was also available at other "levels", so I gave level 8 a try and this worked. The output from my command session looked like:
F3 T>/8 F3 8>Z Spin Down Complete Elapsed Time 0.161 msecs F3 8> F3 8>U Spin Up Complete Elapsed Time 9.250 secs F3 8>/1 F3 1>N1 F3 1>/T F3 T> F3 T>i4,1,22 F3 T>m0,2,2,,,,,22 Max Wr Retries = 00, Max Rd Retries = 00, Max ECC T-Level = 14, Max Certify Rewr ite Retries = 00C8 User Partition Format 5% complete, Zone 00, Pass 00, LBA 00004339, ErrCode 000 User Partition Format 5% complete, Zone 00, Pass 00, LBA 00008DED, ErrCode 000 00080, Elapsed Time 0 mins 10 secs User Partition Format Successful - Elapsed Time 0 mins 10 secs F3 T>After I had done this I was able to remove the drive, test it and confirm that it was working fine. I then did a firmware update which took it from SD15 to SD1A.
And one more thing, my drives were "made in China" so this problem was not just with the drives from Thailand. 
Not only were video clips sharp and highly detailed, but noise levels were also minimal across the board, even in low light. In fact, there were some instances where we preferred the Vixia HF20's low light performances to the formidable Canon Vixia HF S10's.and provides a few still samples of the low light performance.